A credible Rhodiola rosea specification names both rosavins and salidroside, each quantified by HPLC, and confirms the species. The classic traded profile is around 3% rosavins with 1% salidroside, but the ratio matters as much as either number: rosavins are characteristic of R. rosea, while a high salidroside figure with little or no rosavins is a common signal of substitution or blending. Request a fingerprint against a qualified reference sample.
- Specify rosavins and salidroside separately by HPLC; do not accept a single “total”.
- Use the rosavins-to-salidroside profile as a species authenticity check.
- Name the plant part, origin and extraction solvent on the specification.
- Keep a retained reference sample for chromatographic comparison of future lots.
1. Two markers, two different questions
Rosavins (rosavin, rosarin, rosin) and salidroside are both phenylpropanoid and phenylethanol glycosides found in Rhodiola species, but they answer different questions for a buyer. Rosavins are the more species-characteristic group; salidroside occurs across several Rhodiola species and can be present at high levels in material that is not R. rosea.
An offer that quotes only “3% salidroside” or only “total rosavins” is incomplete. A useful specification states both values, the method and the acceptance ranges, and treats the ratio between them as a consistency check across batches.
| Marker | Typical traded claim | What it tells the buyer |
|---|---|---|
| Rosavins (sum of rosavin, rosarin, rosin) | ~3% by HPLC | Strong indicator that the material is R. rosea |
| Salidroside | ~1% by HPLC | Marker content, but not species-specific on its own |
| Rosavins : salidroside | Commonly around 3:1 | Consistency and substitution check between lots |
| Extract ratio only | e.g. 10:1 | No information about either marker |
2. The HPLC method has to travel with the number
Summing three rosavin peaks is a method-dependent exercise: column chemistry, detection wavelength, gradient and the reference standards all affect the reported total. A COA that says “rosavins 3.02%” without the method, the standard supplier and the way the sum was calculated cannot be independently reproduced.
Ask for a representative chromatogram with the first qualification batch. It is inexpensive, and it makes every later dispute resolvable without re-opening the method question.
- HPLC or UHPLC, with column type, detection wavelength and gradient summarised.
- Reference standards for rosavin, rosarin, rosin and salidroside, with purity and source.
- Definition of how the rosavin total is summed and whether it is on a dry basis.
- A representative chromatogram and a retained reference sample.
3. Species, plant part and origin
Rhodiola rosea root and rhizome are the traded material. Other Rhodiola species and aerial parts are cheaper and can produce a plausible salidroside number while failing the rosavin profile. Botanical identity by HPTLC or DNA-based methods, plus a chromatographic fingerprint, is the practical safeguard.
Growing region and harvest season also move the marker levels. Our origin documentation for Hunan and high-altitude botanicals follows the same rule: the finished batch must trace back to a raw-material lot and a harvest window.
- Rhodiola rosea L., root/rhizome, with identification method.
- Country and region of origin, cultivated or wild-collected statement.
- Harvest window and post-harvest drying conditions.
- HPTLC or DNA identity confirmation where the destination market requires it.
4. Extraction, carrier and residual solvents
Hydroethanolic extraction is common for rhodiola because the target glycosides are moderately polar. The ethanol content, extraction temperature and drying method influence both the marker recovery and the residual-solvent obligations. Where a carrier is used to make a free-flowing powder, its identity and percentage belong on the sheet.
Set loss on drying, bulk density and mesh size alongside the markers. Rhodiola powders are frequently used in capsule blends, so flow and hygroscopicity become production issues even when the assay is correct.
| Parameter | Why it is specified | Typical evidence |
|---|---|---|
| Extraction solvent | Determines marker recovery and solvent obligations | Solvent and ratio on the specification sheet |
| Residual solvents | Required by the destination market | GC headspace results with ICH Q3C class |
| Carrier | Dilutes the assay and changes flow | Identity, percentage or explicit none |
| Loss on drying / mesh | Stability and capsule-line behaviour | Physical results on the batch COA |
5. Contaminants, microbiology and documentation
As with any root-derived extract, heavy metals by ICP-MS, a multi-residue pesticide screen, residual solvents and microbiology should be written as a release panel with limits and method references. Alpine and wild-collected material warrants particular attention to the heavy metal result.
The document set should then tie the whole thing together: a versioned specification, a batch-specific COA, origin and identity evidence, and a change-control clause covering species, origin, solvent and assay method.
- Versioned specification sheet with method references and acceptance ranges.
- Batch-specific COA with raw-material lot reference and chromatogram.
- Allergen, GMO, irradiation and BSE/TSE statements where required.
- Written change notification before any process or origin change.
6. A defensible RFQ line
One line in the RFQ can eliminate most of the ambiguity. State the species and plant part, both markers with their methods, the reference standards and the contaminant basis for the destination market, then ask for the same document set from every supplier.
- Rhodiola rosea root/rhizome extract; rosavins and salidroside with acceptance ranges by HPLC.
- Method, detection wavelength, standard source and how the rosavin total is summed.
- Species identity evidence and a retained reference chromatogram.
- Contaminant limits, batch COA, pre-shipment sample and change-control terms.
Frequently asked questions
Can I use salidroside alone as the buying specification?
It is not recommended. Salidroside occurs in several Rhodiola species, so a high value does not confirm Rhodiola rosea. Specify rosavins and salidroside together and use their ratio as a consistency check.
What does a high salidroside / low rosavins result suggest?
It can indicate substitution with another Rhodiola species, blending, or an unusual extraction. Compare against a retained reference chromatogram and request species identity evidence before releasing the batch.
Which method should the COA reference?
HPLC or UHPLC with the column, detection wavelength, gradient summary, and the reference standards for rosavin, rosarin, rosin and salidroside, including how the rosavin total is calculated.
Why does origin need to be on a rhodiola specification?
Growing region and harvest season move marker levels, and wild-collected material changes both traceability and heavy metal risk. Origin documentation also makes an out-of-spec result investigable.
Need the documentation for your project?
Tell us the ingredient, target specification, quantity and destination market. Our team will send a specification sheet, COA sample and a quotation within 24 hours on working days.
Request a Quote Browse Products
Related topic: Rhodiola rosea extract rosavins and salidroside specifications

